DELL PERC H200 SATA 3 UPDATE
DELL PERC H200 SATA 3 ARCHIVE
DELL PERC H200 SATA 3 DOWNLOAD
DELL PERC H200 SATA 3 WINDOWS

Hi Mike, Flashing the firmware and BIOS on an add-in card is likely to be the same level of risk as flashing the BIOS on a motherboard, i.e. The above procedure allowed the H200 I was using to detect and use two 3TB disks. If any indicate a failure, double check that you copied the correct files onto the bootable media. Once booted, change to the folder containing the files copied to the media, above, and issue the following commandsД®ach command should report success before you move onto the next one.IвЂ™d recommend disconnecting any drives from the RAID card before flashing the firmware and BIOS. Boot the server containing the PERC H200 from the bootable media.Copy the version from the sas2flash_dos_rel folder if using a dos boot disk.Дў118ir.bin вЂ“ this is the firmware for the 9211-8i. Sas2flsh.exe вЂ“ this is the flash application.

DELL PERC H200 SATA 3 WINDOWS

I created a Windows 98SE boot USB stick and copied the files onto it.

DELL PERC H200 SATA 3 ARCHIVE

Copy the required files from the extracted archive onto bootable media.

I downloaded the вЂ9211_8i_Package_P16_IR_IT_Firmware_BIOS_for_MSDOS_WindowsвЂ™ package and extracted the contents. I got my copy from (click on the вЂSupport & DownloadsвЂ™ tab, then expand the firmware section).

DELL PERC H200 SATA 3 DOWNLOAD

Download the latest 9211-8i firmware package from LSI.

As the PERC H200 is essentially a rebadged LSI 9211-8i card however, the firmware and BIOS from that card can be flashed onto the PERC H200 to provide support for larger SATA hard drives. In fact the card cannot even detect SATA drives that are larger than this. sas2flsh -o -f 2118it.bin (v19 of the LSI FW this time)ДЎ1.The latest firmware for the Dell PERC H200 still doesnвЂ™t support SATA disks of greater than 2.2TB.

sas2flsh -o -f 2118it.bin (I used v7 first which allows IR IT crossflashing, will ask to crossflash, type Y to proceed)ДЎ0. sas2flsh -o -sasadd 5d4aXXXXXXXXXXXX (16 digit sas address)ДЁ. megacli -AdpAllInfo -aAll -page 20 (document sas address)Д¦. If so is there a separate download for the v7 firmware? Or would the v7 somehow be included in with the v20 that I download?ДЎ. Will / should I first flash to v7 and then to the v20? In one of your posts 'pasted below' you said to flash it to v7 and then to v19. I'll download the ' 9211_8i_Package_P20_IR_IT_Firmware_BIOS_for_MSDOS_Windows.zip' file to get the P20 firmware and put it on a bootable flash drive. Just want to make sure that I've got the steps down correctly, etc. So much info out there, a lot of it seems to overlap. Thanks whitey, I'm in the process of looking thru those links. I initially had a reverse cable, but have since purchased So I think that I now have the correct cable. I can hear / feel it spinning, but it dosent show up in Disk Management. But when I connect a HD to the card with the breakout cable the drive doesn't show up. The card now shows up in the BIOS / System Settings and also in Device Manager as 'Dell 6Gbps SAS HBA', so that all seems good.

DELL PERC H200 SATA 3 UPDATE

I followed the instructions to flash the card and update the driver.

I followed the instructions from here to flash it into IT Mode - SAS HBA crossflashing or flashing to IT mode, Dell Perc H200 and H310Д®verything seemed to work fine (I think). After posting in the other thread, I picked up a Dell PERC H200 6Gb/s PCI-e SAS SATA 8-Port Raid Controller SAS2008 9210-8i 47MCV card. Working with raid cards is all new to me, so bear with me as I try to get this figured out.Д«asically, I need to add a couple additional HD's to my WHS 2011 server, but I ran out of SATA ports on the motherboard. I posted about this on another site and was referred here for further assistance. I was referred to this site for some assistance with a Dell H200 card that I'm trying to get working for my server.

Dell perc h200 sata 3